The actual current is close to 0 A<\/p>\n<\/li>\n
The current is much lower than the configured set value<\/p>\n<\/li>\n
The system cannot reach the expected charge\/discharge current<\/p>\n<\/li>\n
Current output appears capped or unstable<\/p>\n<\/li>\n<\/ul>\n
Possible Causes and Solutions<\/h2>\n1. Schedule\u2019s clamp setting limit current output<\/strong><\/h3>\nIn global tab of schedule file, locate Clamp protections area<\/p>\n
Ensure the entered values are appropriate. For example, if Current Clamp Low is -7A and Current Clamp High is 7A, setting the current to 10A or -10A in the schedule will not exceed the range (-7A, 7A).<\/p>\n
![\"clamp](\"https:\/\/www.arbin.com\/wp-content\/uploads\/2026\/05\/clamp-protection.webp\")
<\/p>\n
Solution<\/strong>:
Remove the clamp value or enter a higher value as needed.<\/p>\n2. Max Current<\/span> setting is lower than the configured current<\/h3>\nIf the Max Current defined in the schedule’s step is lower than the set current, the output current cannot reach the set current.
Solution:<\/strong><\/p>\n\n\n\n\n\n![\"schedule](\"https:\/\/www.arbin.com\/wp-content\/uploads\/2026\/05\/schedule-step.webp\")
<\/p>\n<\/div>\n<\/div>\n<\/figure>\n<\/div>\n<\/div>\n
In schedule file, locate Step Limit tab.<\/p>\n
\n- \n
Increase the Max Current value<\/p>\n<\/li>\n
- \n
Ensure it matches or exceeds the desired current level<\/p>\n<\/li>\n<\/ul>\n
3. Fuse on IV board is broken<\/span><\/h3>\n\nRemove the IV board and check the fuse with a meter set to ohms.<\/span><\/p>\n<\/div>\n4. Switching Power Supply is off or not working<\/h3>\n
If the current is nearly zero<\/em>, the Switching Power Supply (SPS) may not be turned on.
The picture below shows a typical Arbin machine with SPS, the SPS\u2019s air breaker are the white colors in the yellow rectangles. On their left side are light indicator showing V++ and V– (circled in white).<\/p>\nFor smaller machines, the Switching Power Supply maybe hidden inside the chassis.<\/p>\n
![\"arbin](\"https:\/\/www.arbin.com\/wp-content\/uploads\/2026\/05\/arbin-machine-with-sps.webp\")
<\/p>\n
Solution:<\/strong><\/p>\na. For visible switching power supply<\/p>\n
\n- \n
Turn on the switching power supply and ensure the light indicators are on as shown below:<\/p>\n<\/li>\n<\/ul>\n
\n\n\n\n\n![\"arbin](\"https:\/\/www.arbin.com\/wp-content\/uploads\/2026\/05\/arbin-machine-with-spsturn-on-the-switching-power-supply.webp\")
<\/p>\n<\/div>\n<\/div>\n<\/figure>\n<\/div>\n<\/div>\n
\n- \n
If the air breaker is on but the light is off, check the three-phase power supply at the machine’s rear.<\/p>\n<\/li>\n
- \n
If the breaker is on and only one light indicator is lit, the SPS has a hardware issue. Please contact Arbin support.<\/p>\n<\/li>\n<\/ul>\n
b. For hidden switching power supply<\/p>\n
\n- \n
Try issuing a small current using the machine’s lowest range, e.g., I range4. If it outputs the correct current with this range but fails with others, the switching power supply is likely faulty.
Please contact Arbin support for assistance.<\/p>\n<\/li>\n<\/ul>\n
5. V++ or V– is too small<\/h3>\n
The symptom is that the charge current drops when voltage is high and the discharge current drops when voltage is low (e.g., in systems like LBT21). This may indicate insufficient V++ voltage<\/strong>.<\/p>\n
In global tab of schedule file, locate Clamp protections area<\/p>\n
Ensure the entered values are appropriate. For example, if Current Clamp Low is -7A and Current Clamp High is 7A, setting the current to 10A or -10A in the schedule will not exceed the range (-7A, 7A).<\/p>\n
<\/p>\n
Solution<\/strong>: If the Max Current defined in the schedule’s step is lower than the set current, the output current cannot reach the set current. In schedule file, locate Step Limit tab.<\/p>\n Increase the Max Current value<\/p>\n<\/li>\n Ensure it matches or exceeds the desired current level<\/p>\n<\/li>\n<\/ul>\n Remove the IV board and check the fuse with a meter set to ohms.<\/span><\/p>\n<\/div>\n If the current is nearly zero<\/em>, the Switching Power Supply (SPS) may not be turned on. For smaller machines, the Switching Power Supply maybe hidden inside the chassis.<\/p>\n Solution:<\/strong><\/p>\n a. For visible switching power supply<\/p>\n Turn on the switching power supply and ensure the light indicators are on as shown below:<\/p>\n<\/li>\n<\/ul>\n If the air breaker is on but the light is off, check the three-phase power supply at the machine’s rear.<\/p>\n<\/li>\n If the breaker is on and only one light indicator is lit, the SPS has a hardware issue. Please contact Arbin support.<\/p>\n<\/li>\n<\/ul>\n b. For hidden switching power supply<\/p>\n Try issuing a small current using the machine’s lowest range, e.g., I range4. If it outputs the correct current with this range but fails with others, the switching power supply is likely faulty. The symptom is that the charge current drops when voltage is high and the discharge current drops when voltage is low (e.g., in systems like LBT21). This may indicate insufficient V++ voltage<\/strong>.<\/p>\n
Remove the clamp value or enter a higher value as needed.<\/p>\n2. Max Current<\/span> setting is lower than the configured current<\/h3>\n
Solution:<\/strong><\/p>\n<\/p>\n<\/div>\n<\/div>\n<\/figure>\n<\/div>\n<\/div>\n\n
3. Fuse on IV board is broken<\/span><\/h3>\n
4. Switching Power Supply is off or not working<\/h3>\n
The picture below shows a typical Arbin machine with SPS, the SPS\u2019s air breaker are the white colors in the yellow rectangles. On their left side are light indicator showing V++ and V– (circled in white).<\/p>\n<\/p>\n\n
<\/p>\n<\/div>\n<\/div>\n<\/figure>\n<\/div>\n<\/div>\n\n
\n
Please contact Arbin support for assistance.<\/p>\n<\/li>\n<\/ul>\n5. V++ or V– is too small<\/h3>\n
![\"arbin](\"https:\/\/www.arbin.com\/wp-content\/uploads\/2026\/05\/arbin-machine-with-spsturn-on-the-switching-power-supply-2.webp\")
<\/p>\n<\/div>\n<\/div>\n<\/figure>\n<\/div>\n<\/div>\n